Hello.
Today, introducing you microns for molding and assembly of the bracelet with sunflowers.
sunflowers from polymer clay
For u you need to:
• Wooden framework for bracelet
• Clay Titanium
• cord
sunflowers from polymer clay
• Polymer clay
sunflowers from polymer clay
• Pasta Machine
• Toothpick
• Cater leaf
First, we need to prepare the ground for the bracelet. Take the sandpaper and gently walk on top for a bracelet to raise the villi. Liberally grease glue and start to wrap the cord. Cord near the power cord must be very tight lie.
sunflowers from polymer clay
sunflowers from polymer clay
The finished foundation set aside, so dried.
sunflowers from polymer clay
Take the yellow to orange clay, in the proportion of 2: 1. Fold one rectangle.
Roll out a layer as long as the transition from yellow to orange will not be smooth.
Then fold in brusochek and rolled, so as a result you have turned out very thin and long ribbon.
 
sunflowers from polymer clay
sunflowers from polymer clay

Fold it like an accordion.
sunflowers from polymer clay
And then the lower edge of the side with an orange band, pull the stick and rolled to reduce in diameter.
sunflowers from polymer clay
Cut into thin slices.
 
sunflowers from polymer clay

Use your fingers to flatten each slice and give views of the petal.
sunflowers from polymer clay

Toothpick proceed along the recess and squeeze the edges.
sunflowers from polymer clay
sunflowers from polymer clay
Form a small cake, on which will be spread and the petals.
sunflowers from polymer clay
Toothpick lay the first row of petals. They should fit snugly together. On the first row of petals, choose a larger size. Attach the petals on the edge of the cake.
sunflowers from polymer clay
The second row is lined with smaller petals, they should be located between the first row of petals.
sunflowers from polymer clay
For a bracelet it took me four flowers.

sunflowers from polymer clay

Our flowers are missing only midway.
To do this, roll the cane with black clay and cut into slices.
sunflowers from polymer clay
Form a ball, and then with one hand hold him, put it on the middle of a flower.
sunflowers from polymer clay
Scissors make incisions on serdtsevinke.

sunflowers from polymer clay

Still need to sculpt three buds. To do this, roll a ball, and for the convenience of put him on a toothpick.
sunflowers from polymer clay
Take the smallest sections, and overlaid them the ball. The first ball of petals should completely cover the core, and the second edge is slightly protruded. If, among the cuts is not small, then rolled the cane so that it becomes thinner and cut.
sunflowers from polymer clay
Roll out a thin layer of green clay to make our bud sepal. I used the smallest cutting.
sunflowers from polymer clay
Then gave a toothpick texture, fingers pressed the edges, so that they become sharp little and fastened to the back of the bud.
sunflowers from polymer clay
sunflowers from polymer clay
sunflowers from polymer clay
In the same way I’m blinded two more buds.
Make a hole on the back side. Rolled thin thread of green clay, give slightly wavy and insert the tip of the pre-moknuv it into a gel, into the hole. It will stalk.
Now we have leaflets. Roll out a layer of green clay. Then cut out the boat leaves.
sunflowers from polymer clay
Texture to the leaves I made a living leaves, the leaves are picked up, they might have a thick vein net.
sunflowers from polymer clay
To streaks on the sheets of paper you turned right, you need to put plastic on the back side of the leaf, while the veins will go inside and not stick out.                              
sunflowers from polymer clay
sunflowers from polymer clay
Give them waviness.
Roll still green thread and tighten them, that we will fill the void.
sunflowers from polymer clay
Send to all firing blanks of plastics.
 
sunflowers from polymer clay

The firing temperature is written on the packaging of your clay.
Firing carried out only in a closet top land, in any case can not be in the microwave!
After firing, the backside of the product alcohol degrease.
Clay I only use Titan as it remains transparent when dry and tightly holds the glued products.
sunflowers from polymer clay
Apply glue to the back of the flower and attach to the base.
 
sunflowers from polymer clay
sunflowers from polymer clay

First, we glue all the flowers.
Then sticking buds and leaves.
sunflowers from polymer clay
sunflowers from polymer clay
sunflowers from polymer clay
And after our curls.
sunflowers from polymer clay
We give to dry for 24 hours and can be worn with pleasure.
sunflowers from polymer clay
courtesy: rukodelie.usamodelkina
Shares