Casket for garment accessories

Casket for garment accessories

Sharing is caring!

1

2

The entire process is divided into several stages. It is important to comply with the order of operations, otherwise we will have to dissolve Smile . Laborious process, but for us, nothing is impossible

Stage No.1

Outwardly your box may look like anything, this time I decided to try the technique of “Crazy” (as the basis on which the flaps are sewn, use interlining) 

To the side of the box to carve out a rectangle of width 8 cm and a length of 44.4 cm . such rectangles need to carve out 2 pieces – from nonwoven and batting, and a rectangle of lining fabric should be no longer than 2 cm.

3

On the strip in a chaotic manner nonwoven sew colorful patches, front part of the box ready.

4

5

Fold all three layers together and sew the short sides, leaving not captured by the edge of the pad (see. photo), smoothes the allowances in different directions.

6

7

The remaining edge of the closing seam and sew.
Step No.2
Prepare bottom. You need to cut out the cardboard circle with a diameter of 14 cm. The same circle cut out of batting. Of Lining Cut two circles, one with an allowance of 0.75 cm, the other with an allowance of 1.5 cm.

8

Lay off until towards the lining with a smaller allowance. Then put on a lining with a large allowance sintepon top and cardboard acting allowances folded onto cardboard and glue (I usually use glue “Titan” for ceiling tiles). When the fabric glued safely cut off the excess fabric to the surface became smooth. Bottom ready, postpone it until better times.

9

Step No3.

Pockets for threads. I cut out a strip length of 79.5 cm and a width of 11 cm. Fold face to face and sew the long cut, gut-wrenching, then tuck the edges inside the resulting tube, sew blind stitches in the ring.

10

We take the finished piece boxes, twist on the side padding, and put it in ring, which we had made for pockets,another, retreating 3.2 cm at the most boxes and 6 cm on the ring for the pockets. There comes a time when the length is 3 pockets, then you need to measure the length of the ruler and the remaining distance to divide into 3 equal parts (even if there is a little more than 3.2 and 6 cm.) We do this so that we do not get the last pocket noticeably larger than the others.

11

Then sew on the machine, not to fret, I sewed without interrupting the thread (see. photo).

12

14

Treat the upper edge inlay boxes and sew on the inside half of the castle. At the junction of the edges of the lock is sewn rectangle that will hide this place away from prying eyes and picky, so we need a rectangle again later. Place it between the wall of the box and lock and sew one stitch and lock and a rectangle.

13

Step No.4

sew the bottom. Take deferred circle (vykroenny earlier, with an allowance of 0.75 cm), primetyvaem its lower edge to the box bottom and process piping. Done.

15

16

Step No.5

Needle bed. You can make the beds of all sizes and shapes, but if it does not make more than 4 cm., Then under it then it will be possible to hide the “sartorial meter” (do not know how to call this thing). In this case, the diameter of the internal space in the box tiles equals 8 cm, then cut out of cardboard (to make it well worth then) circle diameter of 8 cm, cut out of the padding and nonwoven circles with an allowance of 0.75 and 5.5 cm wide strips and 25 cm long (not considered allowances). Making Non-woven “crazy”.

17

18

19

20

21

Then sew the short sides of the strip in the ring and sew it to the two circles (lining and “Crazy”), leaving no hard-wired portion through which we unscrew the needle bed and prosunem cardboard circle.
evert, invest cardboard, fills the beds and blind stitches to sew up the hole. Needle bed is ready.
Step №6.
Getting to the cover box. For the cover you need to cut out nonwoven circle diameter of 14 cm. It performs “Crazy”, process piping, and sew the second half of the castle.

22

23

24

Now we need to cut out a circle of cardboard that it fits inside the resulting circle, it will be a little less than 14 cm and the circle of padding with an allowance of 1.5 cm.
Then the circle of padding determines the location of the scissors on the cover and mark where sew strips of fabric and buttons. As you can see, I sewed a dense zigzag, and the button sewed to the cover after already glued all the layers right through the cardboard.
Then, just as we do the bottom cover (circle of padding with an allowance of 1.5 cm, padding polyester and cardboard, glue to the underside of the allowances and Trim any excess fabric.).

25

26

Step No.7
Completion.
At Castle dress ,ugly junction closes the second rectangle (I have already talked about it), do it blind stitches, sew along the long sides and the bottom, the top of the reserve is not sewn, anyway we will hide under the cover.

27

28

29

30

Insert the cardboard bottom.
Cooked cover with already sewn stripes for scissors and buttons, apply to the inside of the lid tightly and sew blind stitches around the circumference and start wildly rejoice (you can shout hooray!) because your diligence crowned with complete victory!

31

32

Sharing is caring!