Preparing for a wedding is probably the most wonderful time. But, at the same time – so exciting. And any little thing that at first glance, is such, is able to turn wedding into a fairy tale. Let’s try a little pokoldovat and turn an ordinary reel of adhesive tape in a lovely casket for rings.
For this transformation we need:
– Cardboard reel of adhesive tape;
– Lid from a jar with cotton buds;
– A small piece of clear plastic (can be taken from the packaging of toys, caps of disposable food containers, etc.);
– A thin double-sided adhesive tape;
– Satin white cloth;
– Adhesive (gel moment, Titan, hot glue), with whom some like to work;
– White acrylic paint, acrylic circuit;
– Lace, beads, ribbons, rhinestones and other decorations for the caskets.
Well, let’s start? Forward!
Reel of adhesive tape must be 3 cm wide. Regular scotch tape width of 5 cm, but such a high box we do not need. If you find a narrow spool can accurately cut the usual sturdy scissors to the desired width.
On a piece of cardboard draw out the bobbin and cut around the bottom of a box of our future.
If cardboard is not, you can cut some circles from the usual cardboard. Suffice it to three circles. And another, cutting the size of the inner circumference of the bobbin. It is useful to us later.
Three mug glued together bilateral adhesive tape. Get here is plump bedplate
Clay-gel Moment Donets glue to the reel. Firmly push forward and a little to well stuck.
Sometimes (and I have never since, I’m not a magician – just learning) it is impossible to cut a smooth, perfectly combines with a core circle-bottom. Nothing wrong. This protruding edge by simply cutting scissors and a bit of sandpaper to sand (this is optional if it will undercut everything exactly).
Well, the box is ready! Joke!
It is just blank. While you wait.
You can now begin to cast over the lid. Take the plastic container of cotton sticks. Here such.
the container itself is not needed. We need only cover.
At this stage you can begin to exercise your imagination. I now wanted to without fail, so that the lid was a window in the form of a heart. You can leave the cover tselehonkim or cut a hole in it any shape: round, oval, diamond, drop, etc. But be careful, do not advise to use complex forms (curls, stars and so on. P.), As we will continue to process the hole with a cloth.
So. On the top draw a figure conceived and carefully cut a sharp nozhnitsami.Dlya to cover it was beautiful and the fabric top cover better lay slightly “increases”. You can use this very thin layer of padding polyester. I used insulation tape with a sticky layer. That such.
Glue on the tape to cover a three-layer (syntepon 0, 5 cm. Will be enough and one layer) and do not forget to cut each layer of our window.Then a thin tape extends along the outer edge of the lid and the top. Adhesive tape will fix the fabric on the cover. Here is the cap, Packed tape.
Go to work with cloth. Remove from the double-sided tape protective film. A piece of white satin fabric cover with a lid, taking care to avoid creases. Due to the adhesive tape fabric lies flat and is not in the slide. Gently stretch the fabric on the side of the cover, follow the folds! We do not allow them to get rid of appearance and immediately if the “break through.” Firmly push in the marginalia unfolded cloth that she grabbed from the tape.
Excess fabric along the edges cut off.
Once again, check the cover of the lack of wrinkles on the edge of circumcision cloth you can go lighter, that edge is not showered. That’s what we’ve got.
And now the worst! No, not so bad, but I have little hands were shaking.
Carefully cut the fabric inside the window, and all the heart notching tails pasted inside. Like this.
Made of transparent plastic, cut a thin circle. Its diameter can be taken equal to the inner diameter of the bobbin.
Cutting circle of plastikm paste it into the cover. Be careful with glue, no blur of the plastic, which remains visible in cutting out the window.The part that is not visible paint over white acrylic paint to cover the glued tissue hvostiki.Poka does not look very good, but then we all zadekoriruem.
Cover Edge-processing piping. She closes the fabric edge and serve to seal the box cover that it is well closed.
While we are conjured on the cover of adhesive tape, our bobinka thoroughly became friends (gelled) with bottomed.
Let’s get back to it. From satin cut out a rectangle 23 × 9 cm. And a circle with allowances 1-1, 5 cm. The diameter of the circle is equal to the inner diameter of the reel. Remember, at the beginning we cut a circle out of cardboard? Here on it and draw a circle on the fabric.
The inner walls papered boxes bilateral adhesive tape and glue it neatly Cut length of the fabric.
Papered interior surface tissue and gut-wrenching just as well on the double sided tape glue the fabric on the outer wall of the box.
Remember about the fold! Ghonim them away! Carefully straighten everything and notched fabric, any excess glue on the bottom.
Cut the cardboard yet another circle and glue it to the tissue. Then close all the ugliness on the bottom of the box, put the two parts together.
Bag is almost ready! To close the bottom of a box in the same way as before Wallpapers cardboard circle of fabric and glue it inside the box.
Well, now, almost all! We are done! Bag ready! Ahead of only the most pleasant – decorating! You can take a break for tea and start embellishment!
Further steps may be performed in an arbitrary shape! This way you like. In my box inside there is a small cushion, stitched from the same cloth and stuffed with a thin synthetic padding.
Pillow sheathed on the edge beads.
Even the pillow sewn beads for two rings.
Be bold and embody your fantasies! Decorate the box with beads, lace, ribbons, flowers or ribbons of plastics, paint the contours! Be creative! And you will succeed!