Craft

Flowers from beads

A

B

C

D

Today I will show you how to weave and collect small flower bead. These flowers I love and serve as integral to my flower necklace: it is the average flower in cream necklace, the smallest – in the chocolate and the smallest – in pink. And now you will learn how to do them. Just say, that I did not open the room colors that are used in weaving.

We need:

– Japanese beads 11/0 five different colors

– Beads, pearls or crystals

– Beaded needle size 12

– Japanese fishing line 0.19 mm

– Pliers

– Scissors

– Schemes petals

E

F

Scheme 1

G

Scheme 2

Weave ten large petals of Scheme 1 and five small Scheme 2 For those who are not quite clear how the trailing petals, tells and shows. I plet their flowers mosaic, starting from the middle lobe, the left half of the first, then the right. If you want, you can use a brick weave, then the petals will turn softer and more pliable.

Cut a piece of fishing line a little more than a meter in length. Middle anchoring stop bead. Typed on the line 18 beads.

H

Thread the needle in the fourth bead from the end.

I

And the second row weave fabric, adding one bead of the corresponding color.

J

Now weave the third row of the web, starting as seen in the photo.

K

Finished third row and do the addition on the upper edge of a petal. First strung beads on the line 4.

L

Thread the needle in the first of strung beads.

M

Tighten, another bead strung and are passing the needle into the last bead of the third row – start the fourth row.

N

Wove the fourth row.

O

Begin turning down the bottom edge of a petal. To do this, are passing a needle into the last bead of the fourth row.

P

Deduce thread tighten and drag in the fifth row.

Q

Now weave the upper edge of the half-lobe. To do this, strung beads and 2 are passing the needle into the last bead of the fifth row.

R

Derive the line, tighten and weave the sixth row.

S

Continue turning down the bottom. Thread the needle into the last bead of the sixth series of conclusions and tighten.

T

Begin to weave the seventh row.

U

V

We continue to weave the top edge. Recruit 2 beads and deduce the needle into the last bead of the seventh row. Tighten. Weave the eighth row. Then continue turning down the bottom of the tab (for some reason did not pictured). Deduce the needle into the last bead of the eighth row and begin the ninth.

w

Wove the ninth row.

x

Continue top edge. Two strung beads and deduce the needle into the last bead of the ninth row. Next weave the tenth row.

y

Continue turning down the bottom: are passing a needle into the last bead of the tenth series, we derive the thread and tighten.

z

Continue  upper edge of a petal. Strung this time one (!) Bead and deduce the needle into the last bead of the previous row. Tighten. Weave the twelfth row.

A

Continue turning down at the bottom. Deduce the needle into the last bead of the twelfth row. Tighten and drag in the thirteenth row.

B

upper edge of a petal. Now we are here diminish. Deduce the needle into the last bead of the thirteenth series.Tighten. Weave last – the fourteenth – series.

C

needle into the last bead of the last series. Tighten.

D

And we derive a line in the upper part of the lobe, passing again through the last row.

E

Now drag in more beads to the edge of the petal was smoother.

F

Gone fishing line into the body of the web through 10-12 beads and cut off. So we avoid unnecessary nodes. Next, remove the stop bead and weave mate lobe just as the first, starting from the third row. At the end of the line weaving derive the lower extreme bead.

Now I’ll show you how to connect the petals together.

So. Our line was coming out of the bottom of the beads at the first tab. Thread the needle to the bottom bead of the second lobe from the bottom up. Tighten.

G

The photo shows that one of the ragged edges of the petals. How to weave a petal, I’ll show it some other time.

Thread the needle to the bottom bead of the first lobe in the direction from top to bottom. Tighten.

H

Again, we derive a line in the extreme lower lobe of the second bead from the bottom up. Tighten.

I

Deduce the needle into the second extreme bead second lobe from the bottom up.

J

Perform the needle through the second bead of the first lobe extreme downward.

K

Again, we derive a needle into the second extreme bead second lobe from the bottom up. Tighten.

L

Similarly we proceed with the third and fourth of our extreme beaded petals. Then the line were taken to the body of the second lobe in 10-12 beads and cut off. So join 5 petals in a vicious circle.

M

Do these two terms. Add them so that between the two lobes of one row was visible  lobe of the other row.

N

O

Now sew circles with each other. It’s a pretty chaotic process, there is no single right solution. Importantly, keep in stitching involved two lower rows of beads in the petals, not more.

P

Of small petals woven in Scheme 2, also make a circle, but (!) Is not short-circuit it. Little petals sew together in 3 or 4 beads as described above. We take these petals and figured we turn in the middle of a flower.

Q

Now we fix our design line. I sewed together the first and fourth petals (or, if you like, let’s call them the second and fifth) as described above. However, the crosslinking in fewer beads. Ends as soon as the design will be pretty tough. If the needle does not go to bead, not much persist – beads may break, and have all the twisting. In this case, deploy the neighboring beads.

R

Now are putting our midway to large petals and sew it. Again, there is no the only possible solution. The main thing is to achieve rigidity and do not spoil. We sewed 4 petals from midway. Fifth petal while moving freely.

S

Now fasten the fifth petal. Let it be placed slightly diagonally. Our flower is almost ready.

T

U

Decorate the middle of a beads, crystals or soft tulle.

V

I have my beads until consolidated. This flower is part of the necklace, and I have not decided what color I need serdtsevinki.

Our flower is ready. Admiring 🙂

w

During the discussion of the master class a question, how the beads are attached to the middle,. Today I will try to as much as possible all clearly show and explain.

First of all tell you a terrible secret. The previous master class I wove central – small – rose by slightly cropped scheme (without the bottom two rows), I was so necessary for my ideas. Here is a diagram I had.

x

Flower turns beautiful and so and so. All its previous colors of this size, I spun on the scheme, which gave you last time. I say this now because midway in the usual flowers and trimmed slightly different scheme. The central hole in the flower in the usual way a little less. Therefore, you may need fewer beads to cover her. By the way, the number of beads I have changed, even if the flowers are woven in exactly the same schemes: it is necessary to 4, then 10 – these are the most common options. Even the flowers are different from each other, no matter how hard you try to make them the same.

For example, a small chocolate flower gossip scheme that I gave you last time. In the middle, he has 4 beads.

y

Red flower in the bracelet also gossip on uncut scheme, and in the middle, he has 10 beads.

z

That there are such wonders. Behind this digression finish and pass directly to the master class.

So we need:

– Flower Bead

– Beads (in my case pearls Swarovski)

– Japanese fishing line 0.19 mm

– Beaded needle size 12

– Japanese beads 11/0 or 15/0

– Scissors

– Pliers

The last time I forgot to explain why we need the pliers. I use them in hard to reach places in the assembly when the fingers do not grasp. And sometimes the needle goes in hard times through dtsat bead so it will not break down, do not pull the fingers and pliers. When decorating midway pliers come in handy in exactly the same cases.

So proceed.

Cut off quite a long piece of fishing line, a meter and a half. Fix the line in flower. You can use a variety of ways. Can be attached to the end of the line stop bead, thread the twine through the bead of one of the lobes of the lower row around the middle and go through the body of the petal to the lower edge and lead the line in the middle of a flower. Stop bead with the tip of the cut line. Or you can use a simpler method. Fix the line at the tip of the stop bead (required 15/0 size and transparent), are passing between the bases of the petals through one of the beads and print in the middle of a flower on the back side. It turns out, our stop-bead is our fishing line bundle.

So, we have consolidated our fishing line from the back of the flower.

A

Now draw the needle through the center bead of the bottom row of one of the small petals. Strung bead and bead (I use beads 15/0, but you can 11/0, not to spend money), and then are passing the needle back into the bead on the same side where the beads and lead the line in the same bead of the same lobe, with which we began.

B

Tighten. The first brick laid.

C

Now draw the line through the center of the bottom row of the neighboring bead petals from the bottom up.

D

Strung pearl and bead, pass the fishing line through the pearls and the central bead of the bottom row of our lobe again. Tighten.

E

Derive the line through the center of the bottom row of the next bead petals from the bottom up – this same tab, which we fixed by the assembly last.

F

Strung with beads and pearls, we derive the line back through the pearl and bead center of the bottom row of our tab. Tighten.

G

Now draw the line across the bottom row of the last petal that forms our middle. Note that here I was not able to pass through the central bead, so I have been involved one of the most extreme.

H

Again strung pearls and bead again pass again through the pearls and display the line through the outermost bead bottom row of petals. Continue to sew so that the beads until filled our seredinka. I took it for 3 more pearls. Note that the one pearl that was pictured in the center, as originally sewn to the edge, then just rest her pearls “squeezed” in the center of our circle dance.

I

Now we need to fix this design. If any of our beads, despite all our efforts and tightening, still a little hang out, go through them again scaffold. Consolidated. Now draw the line from the center up and begin to twist our beads as if beads – a flower, a fishing line, which they are attached to the middle – it is their stems. Our task – to tie the “bouquet”. Then Gone fishing line through some of the beads of the bottom row of some of the petals (suit absolutely any), and tighten. After this procedure, our pearls are sitting like a glove.

J

However, this is not the end. If you look at the light, you will see that our middle, “lit.” For that kind of midway I put only three. Our goal – to earn a solid “excellent.”

K

Sew more beads. To do this we derive the line up again from the center of the flower and bead strung with beads, again pass the needle through the bead and print a line in the center of the flower. Deduce it from the back side and fasten it on any beads that you look. Repeat this process two more times. In the photo, I pulled a third of our additional beads to be seen where he was going fishing line.

L

Tighten. Touch all pearls finger, trying to shake them. If suddenly somewhere something does not sit quite securely fasten. Balance Gone fishing line into the body of one of the lobes of the lower row in 10-12 beads and cut off. Done! Admire.

M

N

O

P

Q

Related Posts