Flowers of the foil

Instructions for the production of food foil colors:
1. Preparation:
Of the additional tools you need only a pencil and scissors. Wrap the foil on a sheet of colored cardboard A4.
From the sheet of cardboard on which is wound foil, cut the “main pattern”.
Raschertite sheet of foil with a pencil and cardboard template on the same strip. To foil is not broken, do not press too hard

2. Cutting the foil:
Cut a strip of foil width of 6 strips.
For the rest of the foil, cut into narrow strips in accordance with the markings made.

3. Twisting wires:
Twist of 14 single strips of silver foil wire. Grasping movements crumple a strip across the entire length. Continue crease fingertips until the strip turns into a rough Nyo “sausage” thickness of 4-5 mm. If a strip of foil at the crease accidentally broken, then roll out its wire scraps and either use them where the whole wire is not required before using any link, as will be discussed below under “Connection breaks.”
Hold “sausage” between the thumb and index fingers and rolled back and forth, slowly moving from the beginning to the end, like spins the thread.
As a result, you’ll have a brilliant flexible wire thickness of about 2 mm and a length of about 17 cm. Do not press too hard when rolling the, otherwise the wire can become brittle, and from uncomfortable to weave.
Accidentally torn wire can easily connect tightly twisting the ends together. This connection is reliable, almost imperceptibly, and keeps the overall flexibility of the wire.

4. Weave cornflower (tab)
Fold the wire in half. Depart from the bend of about 2 cm. And again bend the wire. Then after another 2 cm make the third bend. Symmetrical fold the other half delay. The result frame petal.
Take two wires and cut each one in half. Double-coil fix mate delays in the central projection frame. To do this, stand back from the beginning fastened wires about 1.5 cm, attach it across the wire frame, fold the tip of the short itself through the frame, and then remove it from the bottom and back Fold over the top.
The coils of wire should fit snugly on two adjacent ledges just fix two halves of the wire. The remaining half of the wires cut in half and double turns fix each of the resulting pieces in the last two folds of petals.
Press fingers to sharpen the tip petals, giving it a clearer shape. Place all wires inside the frame in one plane and wrap one of the long ends around all the others, fixing them together. Ready petal slightly bend the arc, making it slightly convex. Similarly, make another 3 petals.

5. Stem and middle, cornflower:
Cut the tissue paper into 4 equal parts. Crumpled napkins and a quarter roll between your palms into a tight ball.
Take untwisted strip foil 4 lanes wide and tightly wrap the paper ball its end.
Smooth the surface of the ball with your fingers, improving its shape. Crumple the foil below the ball and roll in across the wire, as we have done this in the preparation of the material. The flexibility of the wire is not required, so the tighter it you roll up, the better. 6. Build a flower: Get ready to stalk and symmetrically arranged around the ball at its end 4 ready petal. A separate wire tightly wrap the stem and the adjacent ends of the petals using the entire length of the wire. A thin strip of foil untwisted cut crosswise into two equal parts and tightly wrap the bottom of one of them a flower. Place the wire sheet close to each other. Several times extreme wrap wire around all the rest, leaving the loose ends of a length of about 3 cm.

7. Leaf:
Take 2 wires. The first (base) bend the arc and put it across the second wire by aligning their midpoints. Fold the wire in half are fixed through the base and fix her a double coil are on the bottom end. To do this, pass it under the base and around the bend on my own, by placing one end of the wire parallel to the second.
Straighten and flatten the wires at the end of the sheet after twisting space and use them to fasten sheet stalk. Similarly

8. KOLOSOK-Stem:
Take the last remaining wide strip of foil and make her a thick dense wire-stem, as you have done for two cornflowers.

9. Corn:
Cut the whole paper towel first in 4 parts, and then each of them for another 4. Take one of the sixteen pieces of cloth, crumple it and roll it between your fingers in dense oblong seed.
Cut the foil untwisted strip crosswise into 3 equal parts. Put in the middle of one of them, the paper grain. Tightly wrap it in foil and left ends of crumple and roll across into thin wires, as you did in the preparation of the material.
Similarly, do another 17 pips. Missing pieces of cloth cut from the remaining two quarters after production cornflowers, cut each one into 4 equal parts.

10. Build spikelets:
By the end of the stem screw ready seed, using fixing one of the tips. Place the coils close to each other.
On the side just below the screw in the same way the second seed. Third seed attach the opposite side of the stem.
Continue to fix the grain, alternating their location until the fix on all the stem 18.
11. Leaf:
Take three wires, lay in a row and twist along their tips. For the reliability of the connection several times strongly press it with your fingers. Leaving the free end of the length of 3-4 cm and wrap the wire around the two extreme rest, locking them together. Spread the wires below the twist. With them, screw the plate to the stem as you already did with the leaves of cornflowers.
If you have any further procrastination, put one, while others do so much more for leaflets cornflowers and cereals, how many will. If you have worked carefully, you can make another list for spikelets and three leaves of cornflowers. Ready screw leaves to stems just below the existing ones. Take the last remaining wide strip of foil and make her a thick dense wire-stem, as you have done for two cornflowers (Photo №5).
12. The assembly of tracks:
Arch leaves rye and cornflowers arc. Beautifully arranged flowers in the bouquet, and the last remaining wire wrap around all three of the stem, fixing them together. The coils are positioned absolutely and close to each other, using the entire length of the wire.
Now you can be made to arrange flowers on black velvet, and you get a nice picture. Either wrap foil glass, decorating it with balls of foil, and you’ll have a beautiful vase for your bouquet.
The work is ready: