Today I’ll show you how to make a jar of ordinary It is a charming little dog, in which you can store all the little things, coffee or spices. The job requires patience and accuracy. This dog can be a wonderful gift to your friends.
To create a dog we need the following materials:
– A glass jar with a screw cap;
– Detergent degreasing effect;
– Corrugated cardboard;
– Scissors;
– Acrylic paints, markers can be;
– Wire;
– A small piece of fur;
– Fine satin ribbon;
– Coffee beans;
– Semi beads;
– Thermo-gun;
– A little padding polyester or other filler;
– Thin cardboard;
– Sacking or coarsely textured fabric for cross stitch (canvas);
– Fine linen (cotton) cloth to match the underlying tissue;
– Acrylic varnish;
– Clay Titanium;
– Paper molar Scotch;
– Brushes for varnish and paints;
The materials are ready, begin to work:
Step 1: Making the base:
Wash the jars with a degreaser (I use washing up liquid or glass) and wipe dry. From burlap (or coarse texture of the canvas, the color of your choice), cut a rectangle width (height) for the size of the height of the jars from the bottom to the shoulders, plus about six centimeters. The length of the segment is equal to the circumference (diameter) cans plus centimeter – one and a half on the pasting seam.
Cut out the fabric are putting to the base, the joint tape is easy to fix a mole on the side that would further joint tissue obtained under foot. From a paper adhesive tape is cut oval (or circle) -buduschee window on the dog’s tummy, which is pasted on the burlap where we do tummy, carefully remove the cloth and cut out a window using manicure scissors.
Then, with the help of glue Titan neatly papered jar prepared cloth. The upper edge of the glue under the belt on the neck, the lower should act on six centimeters. Joint sticking overlap, the front part (the one that is closer to the window) has to be on top.
At the upper edge of a thin glue tape:
Step 2: Make a paw:
In the center of the window at the bottom of the protruding tissue incision is made prior to the jar. Just make an incision on the opposite side of the fabric interface.
On the wrong side of each foot fix a thermal gun and glue to the bottom as shown in the photo below.
Step 3: Make a tail:
The wire is twisted, as shown in the photo:
Then glue the wire to the bottom and the remaining paste over with a cloth:
Cut a rectangular piece of fur, as shown in the photo:
Wallpapers cut piece tail around, carefully, that would not be visible glue. The tail curls “bagel” fixing thermo-adhesive.
Step 4: Make a bedplate, decorate legs and belly:
Tummy circle Wallpapers coffee beans:
We put on the bottom of the thermo-adhesive glue and a burlap or canvas:
Then cut off the excess fabric:
On foot sticking three major coffee beans:
The bottom of the foot in a circle and are pasted over three rows of twine string:
Step 5: Form a dog’s head, ears do:
From cardboard cut out five circles in a pyramid, the largest to be wider than the cover about a centimeter. Followed stick together and stick to the thermo-pistol lid.
According to the rim of the cap cardboard circle glue roll of fabric, as shown in the photo:
From burlap cut out a rectangle for the head, according to the size of the circumference of caps, plus centimeter per joint. The height of the fabric on the bottom with a swirling lid should be up to the coffee beans on the tummy, and on top of about four centimeters above the board on the lid.
Wallpapers cut cloth cap, it is required to do under cover of swirling that have turned the back seam (butt glue overlap) and lugs smoothly and symmetrically.
For the ears bending wire ka shown in the photo:
Then glue evenly on the cap:
Top fix a piece of cloth:
Then, make an incision, as shown in the photo:
And glue the front and rear part of the head:
Paste wire cloth:
Soft fur pieces (the same as that of the tail) cut out two rectangles which are on top of the first glue tabs, and then pasted underneath:
Lugs can be bent in any position:
Step 6: Make tabs:
On thin cardboard draw and cut out the two tabs:
Next, glue tabs to a thin cotton fabric in tone work, be sure to do the right and left foot:
Cut legs with Bending allowance, which cuts do:
Further thermo-gun glue the fabric on the wrong side:
Then, on both sides, legs symmetrically glued to the body dogs:
On top of the two legs decorate twine cord and coffee beans:
Step 6: Make and stick its face:
In the same fabric that we did foot, cut out an oval, a circle which contract the thread with a needle, stuffing synthetic padding, pulls together even more, and fasten thread.
Then the thermo-glue gun muzzle to the dog’s head:
Step 7: Make the eyes and paint the muzzle:
On thin cardboard draw the contours of the eye:
Then use either acrylic paint or markers, as you prefer. Draw the iris, I chose green:
Then draw a black pupils and eyelids:
