-Color electrical tape (or color narrow tape);
-posudinka to dissolve PVA paint ;
mult bag (or food film);
cardboard -kusochek (needed length teapot handle);
-bestsvetny varnish (optional);
– and patience (as always, required).
And, of course, tea – the basis on which we will work. I absolutely tiny, with a lid height – 10 cm.
First, use a colored tape divide into two parts maker. So it will be easier to maintain symmetry vykladyvanii patterns.
Obtyanem film maker (single package) and start to spread on top of threads,
I put the patterns, as they say, “out of my head.” Many looked on the Internet, something remains in the memory, a lot of patterns and surrounds us in everyday life. If you are not sure what to do pattern directly on the film, I advise you first draw it on paper under the pot size and leave a film. When complex patterns, I also do so. But in this case I have a very tiny kettle.
Such patterns can be made at the bottom
and at the top.
The spout of the kettle, we note two rows of twine,
get like this.
Bottom arrange three thread twine.
Measure the tailoring meter spout of the kettle, we draw on a sheet of A4 direct, equal to this length. Along spend one more line spacing -1 cm embed list in the file and put it on him, prokleivaya Titan glue, so this pattern.
Remove it (can be half an hour), and attach with glue to the pot Titanium neck. Everything – the basis of the kettle is ready.
The next step – the most difficult: you have to carefully cut with sharp scissors (can be a knife) lined us tea. Bottom up nozzle,
and also from the bottom near the handle to its upper edge. Cut along with the film, it’s more convenient to shoot.
These holes were from the handle,
This dyrischa – from the spout.
Now we need to carefully glue the cut point.
Glued – can leave until the foundation. and to do items.
Drawn in pencil bottom of the kettle, it is very easy, put the kettle on the list and circle,
and is easy to spread on bottom of a file using Titan glue.
Then we do a pen. Measure the teapot handle and cut 3 strips of soft cardboard. Length is the length of the handle + 4 cm, width 0.5 cm 4 -. Because I wanted to make curved at one end of the handle. Sharpen your carton at one end, and you will also be a curved handle. Cardboard strips add up to three layers
Cushioning and loved jute, promazyvaya little – a little glue.
Next – spout. It is necessary to spread on the kettle. First obtyanite teapot spout film
and you can start obkladyvat jute. Just do not put the thread back to back, let there be a little freer -chut. Do not forget promazyvat glue, otherwise all this construction will not hold.
Leave on the edge of the spout 0.5 cm free.
And place it like this.
Now you can remove the kettle from our harvest and remove the tape.
It remains to make a lid. It’s very simple. Obtyanuli his film
and then jute.
Getting glued parts. First – spout. This is the most difficult. Coat with glue better myself nose, rather than base – kettle.
The bottom of glued easily.
For spout and bottom of a glued. I forgot to warn you try to remove the excess glue, if needed, immediately after being made detal.Raskalёnnoy needle.
Now glue pen. That is what has turned out beautiful.
Tea ready, almost.
It remains to close the gaps that were formed during the bonding of the handle. One the bottom, you see – it is ugly.
Let’s close this place two rows of jute yarn.
Another hole at the top. And measure it
make-to-measure just such a loop,
and close it the hole.
Remains cap. Remove it from the base,
so it is from the inside,
and hoisted the kettle on. You can leave a kettle so.
And you can paint. PVA glue diluted with water 1: 1, add water watercolors. And you can paint.