This flower can be used as an additional decoration rim of hair, hair clips , rubber bands or as a standalone aksessuarv a brooch!
To produce such a flower author will need the following tools and materials:
– Satin ribbon with floral print width of 4 cm;
– 5 cm wide plain satin ribbons;
– A pair of scissors;
– Pin (needle);
– glue gun;
– A decorative element in the form of beads (you can also use the buttons or rhinestones, the authors used an earring);
Getting to the manufacture of homemade !
The first tier.
At this point, the author needed satin ribbon with floral print width of 4 cm, which must be cut into squares of 4 by 4 cm, as well as blue-colored satin ribbon, blue and pink colors, which must be cut into squares of 5 by 5 cm.
It is necessary to take the square and fold it in opposite corners, then fold along the fold line a triangle again.
Lighters must be opayat opening area.
Such work is done with all the squares!
It is necessary to lay down a triangle (of 4 pieces) in a pile in the following order: blue – Blue and pink – flowers.
Pin puncture a stack of triangles, marking the middle.
Fold the stack in half.
Use scissors to trim the excess must be sticking tape.
Hold the line tear with tweezers.
Now you must use a lighter.
It is necessary to trim the excess at the bottom of the petal, and then use the lighter.
Such petals need to make 13 pieces.
Using the glue gun, you need to connect with each other petals.
The first row is ready!
At this point, the author needed: satin ribbon with floral print width of 4 cm, which must be cut into squares of 4 by 4 cm, as well as plain satin ribbons of blue and pink flowers that need to be cut into squares of 5 by 5 cm.
2 pink square must be connected into triangles, then put on top of each other with a bend in the triangle again.
Now you must use a lighter.
Prepare the core tab. To do this, we put a blue flower ribbon into triangles (corners connect the cigarette lighter).
It is necessary to put the flowers on blue triangle and smear it with glue.
Using fine forceps, both the triangle must be wrapped in a “roll”. Reaching the middle – stop!
Wrap the rest of the tape in the other direction. The ends must be soldered lighter.
It is necessary to connect the core and yellow petal.
Worn edges must be cut and use the cigarette lighter.
Petal second tier is ready! Such petals need to make 10 pieces.
Using glue author connects the petals together in the ring.
The larger ring (the first tier) must be lubricated with glue and then put it smaller ring (the second tier).
At this point, the author needed: satin ribbon with floral print width of 4 cm, which must be cut into squares of 4 by 4 cm and satin ribbon monochrome blue, which must be cut into squares of 5 by 5 cm.
Adding tapes into triangles (as previously described). Less tape put not great.
Corner folded the folds to the corner of the base.
Use your fingers to the left keeping the design of the newly formed angle.
The index finger of the right hand must be put in the middle to reveal the crease and middle finger and thumb to collect new wrinkles formed around her finger from pressing.
It is necessary to cut off the excess and use the cigarette lighter.
third row Petal ready! Such petals need to make 6 pieces.
Using the glue gun, you need to connect the lobes to the ring, and then paste it into the ring of the second tier.
In this step, you need to pick up the core of the flower. You can use buttons, rhinestones, beads, beads, sequins (in general, whatever you want!). The author decided to use earring ear. She put the earring in the middle of the flower, and then filled in with the wrong side of it with hot glue.
At this point, the author needed a flower Lenca, which must be cut into squares.
The square should be folded into a triangle, which, in consequence, it is necessary to collect “accordion”. The ends of the shells to trim and fix the lighter.
The resulting shells must be pasted between the petals of the first tier.