Seeing the white table lamp in shop without any jewelry, I definitely decided to buy it to make her something unusual and beautiful.And that’s what came out of it:
To work required:
– Table lamp white color with a white shade.
– Beads red, silver, green,
– Beads with a diameter of about 0,3-0,4mm or large beads of white or cream-colored,
– Fishing line
– 0.4 mm wire,
– Wire for the thicker base – the better,
– Scissors,
– Satin ribbon green.
At first I wove flowers.
Typing on the wire as much as possible without cutting beads and the coil, make a loop.
On the axis of the resulting beads he scored 15 and made one rotation about the axis,
Then add 1 bead axis. All you need to make 3 turns on the 3rd lap twisted together wire left over from the main axis and on which all the beads.
He graduated petal.
Made of 7 pieces.
Then he made the middle of a flower.
For this purpose the wire scored 3 beads, folded it in half and once in the first 2 wire strung bead and scored a number of silver beads, to get around the length of the petal. Next severed wire and won again silver beads, are now comparing the length with the already typed beads. Then strung bead and again 3 beads. Then, holding the last 3 missed beads wire beads to already typed in the opposite direction. I do so even 3 times. Get 5 stamens. In the center of the whole structure put bead light color.
Next he made of green beads sepals.
To do this, dial the bead wire 1, two wire folded in half and has 2 wires at the same time 7 strung beads, again severed wire and beads on each scored for the length equal to the length of the petal or a little more. Again I folded wire and put two 1 bead. Loop gain.
Disconnect the wires put more beads, is now equal to the length of the leaf is already woven. After that missed the wire in the opposite direction through the beads 6, leaving the outermost bead lobe vertex. Then again he won the green beads and missed the wire now through the third bead from the bottom. The result was still a loop, detachable from the previous 2 beaded. Such loops made of 5 pieces.
That’s how it looks.
Now I took the central part (stamens) and bolted to thick wire, which became the basis of the design.
And then, in turn, tightened the circle all 7 petals overlapping each other.
At the end screw the sepals.
The first flower is ready.
Now you need to weave another 4 flower on the same technology, but on each axle with petals weaving reduces the number of beads.
Scourge First beaded with 11, then with 7, then 2 florets with 5 beads of on the basis of the axis.
And in the last 3 colors I did not add the beads on the stamens. Everything else is the same as in the weaving of the first flower.
These flowers are also collected on the individual thick tape and glue gun glue satin ribbon around a thick wire, trying to hide all “black” work. Winding wire ribbon about 10 cm.
But that is not all. Now you need to weave the leaves of green beads.
I do everything the same as when weaving petals, only the axle beads dial 5 to 7 of the central leaf and beads to the side. On each leaf axis go around 3 times.
Each twig with leaves leaves 3 leaves. Such branches need 4 pieces and 3-leaf, that will not be on the twig, I finished them branch.
Therefore weave 5 leaves with beads of 5 to 10 axes and leaves with beads of 7.
Now we take a thick wire and fasten the first small leaf. Glue gun and wire wrapped with satin ribbon, hiding it completely. Primotat 2 centimeter tape attach Man 2 larger leaf, and then wrapped with wire.
Doing these 4 sprigs.
Another 3 leaf leave just like that.
Now take the wire from the first big flower and satin ribbon wrapped 7-10 centimeters. It all depends on the size of the lampshade.
Next, add a sprig with leaves and continue winding.
Again through 7-10sm add flower a little less than the first, and so on alternate flowers and twigs.
Example of the construction on the lampshade, and deciding which end twig – cut off the excess wire. And ends with a winding wire, adding the single leaves.
Then, a thin wire neatly attach a sprig to the shade in the top and bottom. If you want to – “we catch” an additional branch in 2-3 places to make it “do not walk”.
Already it got a very nice, but I did not stop.
And I decided to braid the lower part of the lamp mesh beads. Now, the line took so long to be comfortable to work. In the center put 47 beads and 1 extra beads passed through both ends of the fishing line toward each other tightened the circle.
Then scored on both ends of the fishing line to 23 beads and more beads again delayed the second round. She continued weaving until the resulting chain length does not become equal to the length of the central portion of the circumference of the lamp.
In the diagram I drew a rough grid pattern.
Then he closed the resulting chain – tightening the noose last bead, situated in the center of the very first loop.
And then making the knot, so as not to unravel the chain – began to add a loop at the bottom and at the top of the existing chain.Adding loops should be from the center of the existing loop.
In the following series, I reduced the number of beads, because of the round-shaped lamp base.