How to make toy street lamp and tree for miniature garden

Good day to you inhabitants of the country Masterov.Predstavlyayu part of the work-home pumpkin lantern and tree, bench videli.Eto you have a small public garden in front of the house-pumpkin.

lamp height 16cm in finished form.

We proceed to the manufacture of the lamp, we need: paper, pencil, ruler, scissors, glue, paperboard, corrugated board, transparent plastic cover, acrylic paint, furniture lacquer, optional LED light, thin wire, a resistor.

Take a sheet of A4 paper, damn it lekalo.Ya their numbered to make it easier to explain to you.

Cut a strip of paper №1

Take a pencil or a round knob, and turn promazyvaya glue pva.Kogda all turned to the end, gently pull out the lower part karandash.Eto lamppost.

Cut a piece of white paper №2.Berem thin round stick, the diameter was less than a pencil (I took a thin brush), as well promazyvaya PVA glue, turn, trying to hole bottom tube and gently pull out the brush. Then the tube parts №2 №1 tube inserted into a pre-missed with white glue.

№2 Detail speaks at length of 4cm.

Cut 2 pieces of corrugated cardboard. item №3, make a hole in the center of the diameter of the bottom tube №1, since the diameter of your tube can be more than I do, and glue them together.

Side cut paste thin cardboard on each side, as in the picture.

Cut a piece of cardboard cone konusa.Iznachalno I do not dumal.Ya did on glaz.Vot its dimensions: height 2.5 cm, bottom diameter of 1.5 cm, top diameter of your parts №1.

From the bottom to the cone cut and pasted hung round with a hole the diameter of the parts №1

We sit down on the cone part №1

Insert the details of the item №1 hole №3.Predvaritelno missed pva.Opuskaem glue to the bottom of the cone, just missed the bottom konusa.Mozhno glue between parts №3 and cone to wind a strip of 0.5 cm in height. and over a cone height 0,3sm strip. how did it ya.Posle all paint and varnish.

Take any transparent thin plastic, in this case I used the cover of a cream.

Put the trimmed circular cover on the cork substrate, and a top mold №5 pinned pins and outlines ruchkoy.Vyrezaem and bend along the lines sgiba.Namazyvaem edge of a small protrusion 88 universal glue and connect the region.

Cut a piece of cardboard glued №4 in two layers in the drawing or may be described in the bottom of the cardboard glued transparent fonarika.Detal №6 of cardboard into 2 layers.

All parts are made of cardboard and paint varnish.

You can make a lantern with LED to this svetil.Dlya Do the two holes in the part №4, paste and glue LED.

Merge all the details together with glue 88.Esli do lantern to light the LED to solder wires.

Cut a thin strip of paper folded in half in width 4mm.i.

Paint and cover lakom.Posle cut off the length of the glass edge of the fold and glue glue flashlight 88 to the fold.

Merge yourself with a flashlight stolbom.Esli do light the lamp with the pre-wire pokes through the post hole.

I wanted it even ukrasit.Iz paper strips for kvilinga’s clocked such flourishes.

And from the bottom of the same paper cut here such leaves.

All the lights ready.

Somewhere on the Internet I’ve seen from a wire made tree Something svoego.Pristupim added to the production of wood.

We need: wire, wire cutters, two pliers, needle file, the second glue, toilet paper, PVA glue, paper for kvilinga, shaped punch, acrylic paint, varnish.

Take 2mm.provoloku.Otkusyvaem forceps 18cm long. 4 things.

By connecting a wire between them and stepping back from the edge of 3cm stifle pliers, and a second pair of pliers to twist the wire start to twist length 8sm.Ostavshiesya straighten the ends of shaping the tree.

Bites the wire diagonally across the length of which bit off 5sm.Srez handle needle files.

5cm Glue a piece of wire to wire crown, each provoloke.Kleem second.

That’s what I should poluchitsya.Niz wire wrapped paper skotchem.Esli bend bottom pieces of wire in hand, the tree will be stoyat.Mne for my work turn down them it was not necessary.

Cut strips of toilet paper and wrapped around a tree, after having smeared it with glue pva.Obmatyvaem 2 sloya.Posle drying it is quite durable.

Paint and varnish.

Curly punch in the form of a leaf of paper to make leaves kvilinga.

Each leaf folded in half.

Glue the leaves to the branches of the adhesive 88. I got 160 leaves

Here is a tree out.

In this picture the lantern lit, can not be seen.

Here luchshe.Snimal visible in the dark.

OUTDOOR BENCH: Dear residents of the house Masterov.Rabota Countries pumpkin was delayed, so I want to introduce a little of my work, street skameyku.Ona way, part of the work of the pumpkin house.

Well, pristupim.Nam need: white paper for drawing, pencil, ruler, scissors, cardboard, PVA glue, a second adhesive, abrasive sponge, acrylic paint, paint brush, furniture lak.poloski paper quilling.

Draw a sketch of the side benches which would you like to videt.Mne wanted here takuyu.V further on the design, we turn the strips of kvilinga curls, putting to the figure.

We draw on a sheet of paper patterns and cut out one vyrezaem.Lekalo shtuke.Dalshe will outline on the cardboard, that amount as specified in the drawing, and you can immediately draw on kartone.Bokovaya part 2 pieces, 4 pieces back, sitting just 4 pieces 8 pieces, the upper decorative strip 1pc , rear and bottom decorative strips all 4 pieces.

This curve side chasti.vyrezaem like this.

Under the board puts a cork backing, or can be corrugated cardboard, put a template on cardboard, pinned down, and outlines vyrezaem.Takih details we need to cut out 2 pieces.Further details can immediately draw on the cardboard as I have described above, in the quantities as indicated in the drawing.

With the help of PVA glue, paste the item on cardboard and cut to a thickness of 8 to 9 sloev.Vsego sloev.Zagotovku glued in 8 layers, sections we clean abrasive sponge.