How to make wooden chair: In this embodiment, the manufacture of their own hands Adirondack chairs are stored design features, but there are no intractable carpentry connections. Repeat the project will be difficult, making for our drawings, wooden items and collecting the product by means of screws.
We use 20-mm planed pine boards, galvanized screws 4,5h40 mm 10h60 mm bolts with square head restraint and the nuts and washers. Jigsaw and sander will speed up the process and allow the router manual gently rounded edges, but the workpiece can be cut with a hacksaw and a conventional, manually remove burrs and sandpaper.
The device Adirondack chairs: 1 – back strap; 2 – screws; 3 – the upper cross member; 4 – back leg; 5 – lateral support (spar); 6 – bolts; 7 – arm; 8 – front leg; 9 – seat strap; 10 – support the armrest
Production of details
The most complex elements of the chair – two lateral seat supports. Make spar for a full-size pattern on paper.
Drawing lateral support
Draw the lower side parts, lift the left perpendicular to the first segment, and two more at respective angles to the point A. Mark point C and draw a cutout at a transverse tie as shown in the diagram.
Mark the angle of 75 ° with the apex C, extend the line of his bottom side. Draw an arc of radius 116 mm, measure the angle at point D and connect them to the segment.
Spend rounding between points A and B, using a square mesh or improvised patterns as in the photo
Place the cut pattern on the board, avoiding large knots and leaving little away from the edges of the blanks. Circle the file off the contours and details of using the saw on the straights and curly lines cut the jigsaw. Keep painting tool in the direction of the fibers, so that the wood is less shear.
Drawings of parts: 1 – top rail back; 2 – lower back cross member; 3 – arm (2 pcs.); 4 – emphasis armrests (2 pcs.)
Drawing parts: 1 – back strap (7 pcs.); 2 – seat strap (8 pcs.); 3 – Front Leg (2 pcs.) 4 – rear leg (2 pcs.)
Drawing parts: 1 – back strap (7 pcs.); 2 – seat strap (8 pcs.); 3 – Front Leg (2 pcs.) 4 – rear leg (2 pcs.)
Bring on board drawings of other elements chair, using the same template, or draw a straight on workpieces and marks the next identical item at the first cut.
A rounded armrests structurally important, they can draw freehand or templates. The second item Mark up a mirror to chipping during sawing were below the workpiece.
Sand the ends as possible by connecting the same with the workpiece. Otfrezeruyte edges of the upper surfaces of the armrests and backrest brackets, or just soften the sharp edges of the grinding machine.
Assembling the chair
Wooden furniture always begins to rot from the connection nodes, the internal surface of which can not be processed on the finished chair. Therefore, cover parts before assembling the layers 2-3 antiseptic.
Most components of the chair is connected with screws, guide holes are drilled countersink combination, chosen by the thickness of the screw. When they want to hide the hat, they deepen and stoppered with plugs-adhesive.
Put on the table unnecessary board, and place on top of the left side support and the front leg. Align the workpiece according to the drawing, mark the drilling point.
The circuit assembly of the sidewalls chair
The circuit assembly of the sidewalls chair
Make holes for the screws and fasten the parts together. Install the rear foot, placing it perpendicular to the bevel support. Similarly, collect the right side of the frame. Connect the side of the seat backrest and the lower cross bar of the first seat.
Then attach the remaining evenly spaced slats but closest to the back
Replace the front legs supports, for ease of fixing clamps. Screw the screws armrests.
Secure the top rail of the back, aligning it relative to the lower cross member. It is now possible to correct any inaccuracies accumulated millimeter markings and rough cuts.
Small errors are eliminated shear the head rail and trimming angle underneath. In an extreme case, it is necessary to unscrew the bottom bar and correct recess.
Mark the center lines on the cross and tablets on the central strip of the back. Holding the top of the last hand or taking a clamp, drill a pilot hole and tighten the lower screw. Check the vertical position and secure the top rail.
Screw turns all strips at regular intervals. Take the string and tie one end to a pencil, and the other – to nail fixed to the seat and the backrest joint. Spend radius, trim strips for marking and polish the edge.
To fit the width of the last seat slats, put it into place. Examine the collected sand the chair and marking tracks, chips and other defects. Thoroughly sand the top surface of the backrest and seat parts.
Cover the wood oiled, if you want to keep the natural color. Use the icing on the synthetic resins to create an opaque colored surface
courtesy: liveinternet
Buy Wodden Chair Online
[content-egg module=Amazon]
