How to make goldfish wall art
01
To work you will need:
– Thick cardboard,
– Thin cardboard,
<< >>
– Gofrobumaga,
– Baguette foam ceiling – length 1 m, width 20 mm,
– Thick thread,
– Plastic or glass bead,
– Glue,
– Paint black matte in the cartridge,
– Paint “gold” acrylic,
– Outline of the “golden”
– Sponge
– Scissors and paper cutter,
– Metal ruler,
– Office punch,
– Awl,
– Collar for the finished product.
In this master class, the main parts are numbered. Photographs of parts made in full size, so they can print and make patterns. If for some reason to do it does not work, you can download the template here .

02

From cardboard cut out detail №1 – the main part of the fish.
 
03
Further details will be made of thin cardboard. Cut parts №2 and №3 – lips.
 
3
I give them a convex shape.
 
04
For bonding, I use a universal polymer adhesive «Dragonfly», it is sold as a glue for ceiling tiles and moldings.The adhesive hardens quickly, is almost odorless, easy to remove stains. Clay “PVA”, and other water-based adhesives cause wetting and as a result, warping of the paper.
Glued parts №2 and №3 to detail №1.
 
05
Cut parts №4 – head.
 
05-300x200
Folded “tabs” for bonding. To make this easier to do, pushes place fold a blunt knife from the opposite direction of the bend. Glued to the item №4 details №1.
 
06
For the eyes of fish, I took a plastic ball from the dispenser bottle of vodka. Its diameter – 12 mm. Do the details №4 on the future site of the eye hole of 10 mm diameter. Now carefully dent ball into the hole, pushing it to the paper, but did not break it, and began to place.
 
07
The ball is take out. Cut a piece №5 – torso.
 
08
Unbend “tabs” and paste it to the details №1, summing up the left edge of a piece №4.
 
09
Cut a piece №6 – tail.
 
10
Arches detail to give it the bulge.
 
11
Wallpapers detail on the front side gofrobumagoy.
 
12
I glued ready to tail parts №1, having got the base of the tail under item №5.
 
13
Punchers stuffed cardboard circles and paste them to the parts №5. Each subsequent row is placed in the “checkerboard” manner with respect to the previous one and half covers it.
 
14
So I cover all scales of the fish body.
 
15
“Flakes” to speak on crop the top and bottom edges.
 
16
Cut a piece №8 – dorsal fin.
 
17
I highlight details of the bulge and Wallpapers gofrobumagoy.
 
18
A pressure-fin with the reverse side of the part №1. “The tongue,” do not need to bend.
 
19
Cut a piece №8 – gill cover.
 
20
Glued to the item №8 parts №5.
 
21
Cut a piece №9 – the bottom of the crown.
 
22
Cut a piece №10 – the top of the crown.
 
23
Is folded to detail №10 «tongues” and paste it to the details №9.
25
Now, “where” the trimmed edge of the crown, so that it exactly matches the curve of the head.
26
And glued the crown on the reverse side of the part №1 over his head.
27
Cut 2 pieces. Details №11 – front fins.
28
One of them doing a convex, the other – concave. Wallpapers gofrobumagoy both of the details.
29
Cutter at a distance of 5 mm from the lower edge of the trunk make a cut.
30
The cut and paste insert convex fin.
31
Near the back of the concave parts №1 pasting fin.
32
Cut 2 pieces. Details №12 – rear fins.
33
One of them doing a convex, the other – concave. Wallpapers gofrobumagoy both of the details.
34
Glued tail fins is similar to the front.
35
Adding decorations on the gill cover to the crown. Glued eyelashes.
36
I turn to the manufacture of the frame. On paper, I mark up the outline of a future framework. I chose a rhombus with the inner part width of 200 mm and the ratio of the diagonals of 3: 4.
37
Right on the mark up scheme, and then cut off the cutter foam sides of the frame. Parts are the frame. Now you need to give the glue to harden well.
38
To give greater strength can be on the back side of the frame at the junction of the sides heated soldering iron to press steplernye staples. Staple length must be chosen so that they did not come out on the front side.
39
From thick thread doing network. To do this, the sides of the frame on the back side with an awl make small blind holes in which the ends are attached to the adhesive filaments.
40
To decorate the frame using polubusiny pearl and crown puck. However, they look very nice.
41
Washers pasting the corners of the frame.
42
That’s turn came to painting. Styrofoam, of course, a good thing, but the paint from the can “corrode” it. The left part of the sample I covered acrylic primer, right-left “as is”. Visible results paint black paint from spray painting and the subsequent “gold” acrylic. Therefore, the front side of the frame is primed with acrylic paint.
43
Cut a piece №13 – scroll.
44
I spin through the tips of one up and down.
45
Glued fish and scroll to the frame.
46
The product needs to be balanced.
On a vertical surface, such as a door jamb, make using the plumb vertical line and a long needle is suspended from the frame so that it does not touch the walls. The position of the lower corner of the frame relative to the plumb line determines which side and how much weight you need to add. You can use pieces of lead or metal parts.
47
Matched balance invest in specially made hole soldering iron on the reverse side of the frame.
48
To seal the back of the frame strips of cardboard.
49
I paint with black paint product. If you use water-based paints, paper may bend. At the same time the paint-spray allows you to blow out all the difficult places on the product. I use black matte paint in the can «Mixon.Hobby Lack ».
50
With the help of sponges light strokes nanoshu “golden” acrylic, to highlight relief. The inside of the scroll leave unpainted.
51
I inserted in place of the ball. I glued in polubusiny washers.
52
 Gold circuit inscription do.
53
On the reverse side of the frame do fasteners. This loop for the frames, can be found in the baguette, frame shops. To be safe, I hooked loop screw planted on the glue.
54
Ready.
55
With the outbreak.
56
What do you wish? !!
57
courtesy: liveinternet
Shares