I would like to present you a master class on creating candy “Mishkin joy.”
For this we need:
– Plaster on wood;
– Automotive putty;
– Acrylic primer;
– Print with motive;
– Glue for decoupage;
– Acrylic paint (white, black, red, yellow, green);
– PVA carpenter glue (not to be confused with the building);
– Adhesive gel-point;
– Polyurethane varnish, water-based;
– 3D varnish;
– sandpaper;
– Masking tape;
– Silicone mat (bought at a hardware store);
– Sponges, brushes;
– Clerical or collet knife, scissors;
– Gloves;
– Spatula;
– Disposable plates (instead of the palette);
– Bear figure from Kinder surprises;
– And the harvesting.
To begin with carefully shpaklyuem all seams and joints. Dry them (preferably overnight).
Carefully, very carefully skins to plaster remained only in the recesses.
Here on this photo shows, where there were irregularities.
That’s what happened at the exit. Candy ready for further decoration.
Now we need a silicone mat with a “honeycomb” and automotive putty spatula. This putty is necessary to work on the street, because it is toxic. Spread on a plate disposable one teaspoon and add some filler hardener from a tube, mix. Do it quickly, otherwise it will dry up (so the process I describe only – there is no time to photograph).
Quickly “shpaklyuem” our “cell” (if the mixture is not enough, then breed more and continue). We fill our mat and leave to dry for about three hours.
Take the sandpaper and skins (this is best done on a newspaper, and then throw it with the trash).
The skins until until you see all the jumpers “hundreds.”
Here’s what you should have!
We take out the finished “cell.”
On the PVA carpenter on one piece carefully glues.
The final line of “honeycomb” doing a rough, discontinuous.
The remaining “cell” office knife divide in half.
Sticking missing halves.
Left to dry for a day.
Gruntuem whole house from the outside.
While the primer dries, prepare print with the motif (those reasons I created in Photoshop: took dosochki background and drop “planted” polevyÑ‘ flowers, butterflies added).
Cut motives.
Soak (if plain paper office, the pre-fibered it).
Sticking.
Excess gently sanding.
Before you glue under the roof, we try on the motif, buckle, crop. Now you can glue.
Carefully dry them.
That’s what we should have at this stage.
Tinted ribs gently, trying to get to the color motif (I did not succeed, but in this case – does not matter). For these joints, I used black and white paint
Masking tape close motif near the junction with the roof for even coloring.
And so we paint the whole house. Dry them.
Yellow paint with a brush, paint over our “cell”. That brush! To paint goal of deepening.
Thin brush paint drips honey.
The result at this stage.
Belisle put patches on bruises honey.
Mix yellow with red, white and add a little stain going into “cells”.
While the roof is dry, zaymёmsya pedestal house. Use the palette knife a thin layer of filler on the band stand. While the plaster is not dried up, presses the flat palette knife and then tear off sharply.
The result was an imitation grass. So we are doing on all sides of the pedestal.
We select the color to the grass on the motif (mine is not immediately turned) and paint over the “weed” of the filler. Carefully dry them (better to leave the house for the night).
Varnishing the whole house up to ideal smoothness. Dry them. Only after this knife cuts through the windows of the collet and the doorway.
3D paint smudges highlight of honey on the roof (each party must thoroughly dry in a horizontal position).
At the time of gel sticking bear.
We admire the result.
courtesy: liveinternet
