How to make marigold flower

Dimensions are guided by a smaller flower diameter = 9 cm.

Of the green paper cut out a circle in = 2.5 cm (or circle of iron 5 rubles).
A strip of paper folded height 4,5h10 see accordion and cut detalku- pictured it from me first. for the first series of 6 pieces detalek necessary. Further, each separately detalku folded in half (2), and then folded with tweezers Circuits begin to fold to the center, as if the veins do-fold (3.4), then turns around and gently align (5).

On the green circle is pasted so all six petals. Similarly, we do petals for the second row and paste them on top of the first row between llepestochkami first.

The third row similarly do 1 and 2 rows and paste the petals on the 2nd row between the petals.

The following three rows of strips do 4 x 8 cm. And fold it like an accordion and cut semi-oval Circuits without vystupika is in the forefront. These petals will be slightly less than in the first three rows. For three rows should be 18 detalek. Each lepestochek folded in half and make the folds, veins. Each number is pasted on the previous row, and between the petals. Likewise, but from the strips have a height of 3.5 cm, and cut into petals is done for the next 3 rows. and pasting them.

It turns out this polutsvetok.

Three strips of paper h = 2 cm darker tone than the petals of a flower, cut fringe. The fringe should be no higher than 1 cm. To strip did not cut, I usually applied to the strip, and I cut the railway line.

Take 1/2 page in tone petals and a height of 3 cm fold in half and again in half and cut here such Circuits. By the end of the strip is not dorezaem 1 cm. Expand and tighten them. This will be the very first thin and long petals at the midway.

From 1/2 strips of paper to match the petals and 3 cm wide cut just such a piece with folded strip in half and half again. By the end of the strip is not dorezaem 1 cm. There is already one lepestochek folded in half and make a crease-streaks and then spread petals. This is the second row from the midway.

Last detail – the picture a little bigger.

All pre-cut strips of glue to one long: first strip with a fringe, then striped with long, narrow leaves, and then strip with broader petals. Start spinning on the strip with a fringe.

It turns out that’s so middle, that is glued inside the flower. You can make the middle of a bit fancier and, if the latter is a strip made of 1/2, and from the whole strip.

That’s what we’ve got.

Two strips 3 cm wide (yellow and green) put together and cut into small fringe of 2 cm and twist into a tight roll.
1/2 4 cm wide strips of yellow and green paper to superimpose one on the other and cut fringe bigger (2.5 – 3 mm each needle), gently twist the needles in pairs yellow with green together. Donakleit stranded on a tight roll. Insert the wire in roll and wrap the bottom roll and a thin wire gofrobumagoy.

I got here a bud. It is, of course, a little yellower than nature. It should be added, probably more yellow.

And now- leaf

Take paper or denser than the office, or as in my case, glue the two sheets of office paper and let it dry. Fold the paper in half and dried cut here is a form of a complex piece of paper (it can be more or less).

On pieces of paper to make small serifs. After that, each piece of paper folded in half on a branch.

Turn the sheet to the other side, put on something soft and rounded tips of the scissors or a special. slightly twist the tool them back. I have here a sample taken in haste, already in pursuit, and only one layer of plain paper. It is evident that the leaflet was not very clear, as in the photo 16.