I bring to your attention my version of creating Peony- roses.
Materials:
1. Foamiran 2 colors – for roses and green for the leaves (I used an Iranian).
2. Thermo-glue or super glue.
3. Mold sheet rose (although it can be without him …).
4. Scissors.
5. Sponge dish.
6. rounded object Bulka – I bulb from the lamp))).
7. Iron.
8. Paint tinting leaves – acrylics, pastel, dry or oily.
9. Nail acrylic (or optional presence))).
Petals №1 3h3,5 cm – 30 pieces (I cut out squares of folded pile).
Petals №2 4×4 cm – 13 pieces
Petals 4,5h5 number 3 cm – 15 pieces
1 and 5 sepal leaves
Petal №1.
Heat the upper edge of the petal fold it like an accordion, and scroll fingers.
Just straighten. So we treat all 30 petals.
In profile …
Heat the upper edge of the petal. Adds his accordion and scroll fingers.
Hold curled end putting a middle portion of the petal to the iron, heat and immediately transfer the tab on the sponge.
Burst midway lobe suitable subject …
We process all the petals number 2
Petal number 3.
Heat the 2 3 petals. Putting his accordion and scrolls.
Use your fingers to drag a tab forming a bulge in the upper part of the tab.
So we treat all remaining petals number 3
Assembly.
1 segment will consist of three petals number 1. Take 2 №1 petals and glue them together with a shift of about 2-3 mm.
Line – glue place.
The inner petal is turned off as in the photo. A little glue in the place where my tip tweezers.
3 is pasted as a tab on the photo.
Line – glue place. Merge Region 1 and 3 petals.
If necessary – to glue the edge of 3 petals …
Putting it all 10 segments.
Merge 2 segment …
Place glue application
Collect 2 portions of 5 segments and connect the halves together.
Take 5 petals №2. Pasting. 5 petal comes under the first.
Place glue application.
Glue the remaining 7 petals №2 second row.
Petals №3. The staggered glue 7 petals.
We finish the last row of petals 8 №3
Because this is my first u by foamiranu I terribly nervous. While juggling a camera and a gun with kleey middle, lay not so … For this I had to paste a piece of malyuyuyusenky Thomas into the middle of a
Cut leaves and sepals.
Make a lateral incision along the edges and sepals, and leaves
We put a leaflet to Molde (Mold if not, then the veins can be drawn by hand)
In general, you can work with Molde on everyone. But I do so – I personally think that the so-obtained brighter streaks … Who else used to)))
Half sheet with Molde are putting to the iron … And immediately squeeze the heated part at Molde.
Holding the treated part of the heat the second part of the leaf. Squeeze. Now you can remove the entire sheet of paper with mold.
We process all the leaves. Toning (optional).
Today I’m going to use oil pastels (scarlet). Toning leaves and sepals.
Sepal warms to designate notch.
Fold. And grind the tips of his fingers.
We put the ends of the leaves to a second one to the iron to form a toothed edge …
I cover leaves a glossy varnish, but you can not do this …
Glue sepal …
Now the leaves ….
Almost done. At me it is a decoration in her hair for a flamenco dancer …
By the same token, I did Peony- rose from zephyr foamirana … It is a pity that the photo does not convey the whole of lightness and transparency of this material …
Anyone who mastered my post until the end – many thanks!
I want to apologize in advance – this is the first MC. If something is wrong – please, tell me – I’ll correct …
Thanks to everyone who looked!
Leave a comment – thank you so much !!!
Peace and happiness to your home!
courtesy: stranamasterov.ru
