Good evening! It has long wanted to come up with a replacement area, or what that jewelry made from metal .. Now all gone up so much, and how it would be desirable ….
of something that is not expensive …. to create a profitable product in general “porridge from an ax!” And recently, it dawned on me! So I took the idea to the corners.
Long time I lay clay samozastyvayuschaya, bought for frames and cameos by silicone molds .. but I did not like clay to make, as it is decreased during solidification and frames and burst broke at Palam … but now decided on the experiment with frame, because the clay dries it becomes very strong and not so fragile such as gypsum ..
In the photo 3 upper corner it’s clay, and the lowest is a metal angle which I bought in the store
Here is this clay. I took a small piece of slightly moistened with water so that it became softer and more elastic.
I used to sculpt dostochku for sculpting clay and tselafanku
when bruised clay and cooked tsellofanku, I smeared the place where I will roll your ball of olive nursery,
Only a very little … so that the clay does not prilepala to cellophane. I cover with cellophane and a ball is rolled, it can be absolutely any round object like me …
unrolled about 2 millimeters thick, put a corner, carefully pressed, but do not flatten so that the terrain fought on clay, and with a toothpick to trim the edge, looking around them as pencil
and again a little squeeze that all convexity properly displayed.
Then he shifts the edge shooting from the corner of the clay, sooooo tender
that’s how beautiful .. left edge can be a bit smooth toothpick moistened with water a little bit, and the edges are smooth rather than ragged
I took one corner pressed face first, and the other pressed the wrong area
when the corners have dried you can begin to paint. I show watercolor and color of snow, just here no matter what kind of paint you use,
Only the main color in the slots so that was dark. I’m a little mixed and brown and black ink
Now something similar happened, but I’m still just experimenting …. without even knowing what happens
I’ve done this much, made several different parts, even tried to make a hole as the holes on the original, and even tried to make the medallion …
Now we proceed to paint for metallic effect here I painted this acrylic paint
to start taking the brush on the rough and flat, and start with a bronze paint.
on the tip of the brush and rub the paint is typed on the paper so that it was almost nothing left, that is, make it semi-dry,
and as the acrylic dries quickly making the whole procedure very quickly, as did the semi-dry brush starting to drive on a corner ploshmya brush, so to paint only the convex part.
I do not show photos where paint gold paint, but the process is the same, a little over a bronze just gold paint
there you are
but my corner with holes …. when I started to do what it has done it too thin, and it began to break down in the process
So he finally fell on the battlefield ….. first attempt came out lumpy as they say!
But I do like the area with holes that I decided to quickly repeat the process
All the same I was doing in the photo 3 and 4 made here …
holes and I also picked out a toothpick
inside the hole, I also stroked their soaked toothpicks
I cut and removed from the film
thickness of approximately 2.5 mm
All the same, carefully remove the
turned out pretty good, better than the first time!
rear part
laid on dostochku exactly smooth, even layer to withered
now dried
without any cracks
our paint the dark colors
is back, I have decided there is no paint, just paint over the edge because all the same what it will stick
nice work! Only the color is too dark lightish
original is dark, you need to fix … so I repainted
that’s turned out better
all this in an enlarged form, but when you look at your hand then do not distinguish …
if you do not make the original metallic Area
These two options have very organized
is now applicable to a beautiful piece of paper and see how some would look …
to the left the metal, with the right plaster
I have not had time to think of anything with them, so I put only … but still the effect is stunning! Now solved delema … do not need to buy as many corners and wasted so much
Now with holes little corner
and again all together for comparison
I would be glad very much …. if all the achievements will be useful !!!!
Thank you for visiting me, and thank you for your feedback!
courtesy: stranamasterov
