How to modeling carnation from polymer clay

Modeling carnation

Sharing is caring!

How to modeling carnation from polymer clay

Modeling carnation (1)In this master class used Modern clay, also make good use of Luna clay Clay for flower tinted to the desired color of oil paint. The work with the likes of clay I always use oil paints. 1. Roll the clay into a plastic sleeve and cut Cutter wheels for pinks, here I used the largest diameter – 2 pc and the next smaller diameter

Modeling carnation (2) Modeling carnation (3) Modeling carnation (4)3.BASIC stack rolled along the edge of the cut circles, so their rasfaldit

Modeling carnation (5)

Here’s what you should have

Modeling carnation (6)

Then, to give naturalistic flower walk on the edge of a stack of ribbed

Modeling carnation (7)Then an incision in the circle into 4 pieces before reaching the center.

Modeling carnation (8) Modeling carnation (9)

4. Next, do the workpiece to the base of the flower, it is necessary to take a piece of clay measuring about 1cm.

Modeling carnation (10)Roll drop Wear on wires №18, previously done at the end of the wire loop grease drop of glue

Modeling carnation (11) Modeling carnation (12) Modeling carnation (13)

Dress up the prepared circle of petals come together prisbarivaya opposite to each other, and then the rest dva.Nachinaem formed with smaller circles.

Modeling carnation (14) Modeling carnation (15) Modeling carnation (16) Modeling carnation (17) Modeling carnation (18) Modeling carnation (19)

Then oil the glue at the bottom of the flower (it was the first round) and dress the next round and delema too, that first round

Modeling carnation (20) Modeling carnation (21) Modeling carnation (22) Modeling carnation (23) Modeling carnation (24)

Similarly, the act and the other two circles are more. You can take 2 or 3 laps, then turn out flowers of varying degrees of openness. We reserve the flowers to dry down heads

Modeling carnation (25) Modeling carnation (26)

5.Delaem sheets
Roll the clay into a plastic sleeve and cut Cutter sepals for carnations -. Two sizes run your finger along the edge at an angle to the edge was as thin as possible. Make the impression on the Molde to Lotus or any other, which has a thin lane structure with 2- sides Podkatatkraya stack Give the leaves a little to dry and then compress the stack at the bottom of the base sheet iostavit to dry. 6. Do sepals, they too are 2 sizes, so I take the smallest boat to the first row of the sepals. They must also be stamped on Molde, which has a thin lane structure Grease adhesive base studs and paste the sepals in a circle. The lower sepals are usually very small, so they are still cut off by half and glue the bottom of the second row. Such -5sht sepals.

Modeling carnation (27) Modeling carnation (28) Modeling carnation (29) Modeling carnation (30) Modeling carnation (31) Modeling carnation (32) Modeling carnation (33) Modeling carnation (34) Modeling carnation (35) Modeling carnation (36) Modeling carnation (37)

Buds can be pasted one next sepals 8. Painting – oil paint, to paint with a brush semi-finished flowers 9. Stem. Lubricate glue wire and break in clay piece length of about 5cm, slightly thickening the base of the segment, thus forming nodes on the stem carnation. At the base of the stem podkatat stack, moistened with water – so you can iron all irregularities Then again, the lower part of the wire grease glue and swathes of the next segment in the same manner Give stem dry. Sticking at the base node lists. A drop of super glue put on the leaf base.

Modeling carnation (38) Modeling carnation (39) Modeling carnation (40) Modeling carnation (41) Modeling carnation (42) Modeling carnation (43) Modeling carnation (44) Modeling carnation (45) Modeling carnation (46) Modeling carnation (47) Modeling carnation (48) Modeling carnation (49) Modeling carnation (50) Modeling carnation (51) Modeling carnation (52)

Courtesy: marrietta.ru

Sharing is caring!