Now, if you recall, when we designed the patterns for our bodices, we left it at the point where the underdress neckline was higher than the overdress neckline so that the underdress neckline would show. But what we want to show is a strip of puffing that we’re (ostensibly) going to insert into the underdress neckline. So we need to address that situation right now before it goes a step further.
 ruched neckline
Pattern
I think an inch and a half is gracious plenty for a puffing strip. So we’re just going to lower the underdress neckline by 1 1/2″.
 ruched neckline
The puffing strip is going to be a straight strip of fabric, so we won’t really need a pattern piece for it. So we’ll go ahead and add the seam allowance back on to the neckline before we cut it out.
We’ll consider here for a second what the puffing strip dimensions need to be. As for length, since we don’t want it to be frilly-puffy, just moderately puffy, I think we’ll measure the neckline and cut the puffing strip 1 1/2x the length. We could measure the pattern pieces at this point, or we could measure them when we’ve sewn the shoulder seams and the whole neckline is waiting for us to stick the puffing in. I think that’ll be easier.
The width of the puffing strip is like this: We want the final strip to be 1 1/2″ wide. It needs a seam allowance on the bottom, where it adjoins the bodice neckline, but it does not need a seam allowance on top since we’re going to bind it.
Now we need to sew up the bodice. We’re going to line this bodice completely. First, we’ll start by cutting 2 backs and 2 fronts on the fold:
 ruched neckline
Shoulder seams
Now we’re going to sew the shoulder seams together. Each front shoulder seam goes to the shoulder seam of a different back piece, and then the remaining back shoulder seams go to the remaining front piece again. So that the whole thing makes one big happy circle:
 ruched neckline
What we’re going for here is a lined bodice without a center back seam, which make more sense if I fold the lining underneath, like this:
 ruched neckline
Inserting Puffing
Get it now? Good, because here comes the puffing strip:
 ruched neckline
The puffing strip is a straight strip cut lengthwise, with both ends finished and gathering threads run down the long ends. A fairly innocuous puffing strip, all in all.
Now we’ll find the precise place where our back pieces are supposed to fold over (which is not the center back, which would have made it easier to say), and put a pin there.
 ruched neckline
Now we’re going to open the neckline up and place the finished ends of the puffing strip right there, cozied up to the pins, and the center of the puffing strip at the center front. The puffing strip and the bodice are right sides together.
 ruched neckline
Then we’ll pull up the puffing bobbin threads so that the puffing strip fits the neckline:
 ruched neckline
adjusting the gathers so they look nicely distributed, and pinning many, many times. Now we’ll just sew that down, along with the inner gathering thread.
Once that’s sewn down, pressed gently, and good to go, we’ll place the lining on top of the puffing, making a sandwich, and sew that down:
 ruched neckline
See the puffing in between the layers? Now we’ll press the seam, trim it, and turn it right side out:
 ruched neckline
A row of edge stitching at the base of the puffing, through all layers, makes this look very crisp. Do notice, if you would, that if we’d taken big clips out of the seam allowance they would be very obvious at this point.
Now we’ll just pull up these little gathering threads that we put at the top of the gathering strip:
 ruched neckline
 ruched neckline
Binding
Now we’ll bind that top edge, okay?
First, we need a binding strip. This time we are going to use a French binding. The width of the binding needs to be 6x the finished width of the binding, plus 1/4-3/8″ to allow for folding. The length needs to be the length of the gathered puffing edge, plus a couple of inches. This measurement doesn’t need to be very precise, as we’re just going to trim the ends when we get to that point, but we certainly don’t want the binding strip too short. This strip, since it’s going around a curve, needs to be cut on the bias.
The strip is folded, wrong sides together, and pressed.
 ruched neckline
Now we’ll pin the long raw edges to the raw edge of the puffing strip, with the binding on the wrong side of the puffing and sew that carefully down.
 ruched neckline
Here I’ve sewn again 1/8″ from the first stitching and trimmed the seam allowance close to the second stitching.
Now we’ll fold that binding around to the front and pin it so that the fold covers the stitching on the front:
 ruched neckline
The ends need to be folded in like this:
 ruched neckline
Now, slowly, because we’re going around a curve and this is a focal point in our dress here, we’ll edgestitch close to that fold to sew the binding down.
 ruched neckline
Side Seams
Before we can put this on the dress form to look at it, we’ll need to sew up those four little side seams. Bodice to bodice, lining to lining.
 ruched neckline
Pressing those and putting them in place lets us look at the bodice:
 ruched neckline
We did not baste the armhole and its lining together because we’re going to need it loose when we attach the bodice to the skirt.
Here’s a closer look at the finished neckline:
 ruched neckline
And here we are so far:
 ruched neckline
Now all that’s left is to create the blue bodice and sew it all together. Whew! Which we’ll do next time.
COURTESY: childrensfashionworkshop
Shares